Diorama Evilface's Fourth Circle of Hell - Stand Decals - Updated 5/23/2020

[EVILFACE]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 11/18

Awesome mate.

:rock :rock

Who's this Dredd guy?

:dunno some armored dude

:rock

I really like the last Clockwork one!

I dig it too!

 

[Yodasodabo]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 11/18

Love them Mr. Evil Face Sir! The quality is the ish man, def will be needing more. Thanks!


Sent from my iPhone using Tapatalk

 

[mattdorris]

Evilface's Fourth Circle of Hell - Stand Decals - Updated 11/18

Pm sent Evilface

 

[MrRabba]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 11/18



Perfection, thank you buddy!

 

[EVILFACE]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 11/18

Love them Mr. Evil Face Sir! The quality is the ish man, def will be needing more. Thanks!


Sent from my iPhone using Tapatalk

Thanks. That x-men one was fun to design up :rock

Pm sent Evilface

gotcha!!

Perfection, thank you buddy!

Thanks,looks good.

 

[a-dev]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 11/18

Got my set of Terminator decals today, these are fantastic, better than the graphics on the stock HT stands. You weren't joking about your new one for The Terminator, that one is very special, angling it to a light-source creates an awesome effect. I think I'll put a layer of plastic between it and the figure's boots, don't want it getting scuffed.

+1 Feedback imminent.

 

[EVILFACE]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 11/18

Thanks. Those are cut from brushed aluminum. Shouldn't need any plastic on it, I've had figures on them for years with no problems.

 

[a-dev]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 11/18





Look at thaaaat! The gleam off it. Stunning.

Now, my hand slipped and I ended up getting glue where I didn't want it so I had to place the nameplate further back than is typical but I feel it's no biggie.
Also that's the MMS136 with the pants and boots from MMS238. I think they are better suited to this figure with it's smaller head actually. For some reason the 238's big head in combination with these relatively small boots looks wrong to me.

 

[EVILFACE]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 11/18

I like the bushed too. Much more machine like than red.

That looks good! I overpaid again for some boots and pants so all three of my T1's match.

Yea the plates aren't always in the same place. When you remove them there is an outline where they are supposed to go, but don't always end up there.

 

[mattdorris]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 11/18

Nice Terminator stand. Makes me want to get one for my DX10

 

[a-dev]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 11/18

I like the bushed too. Much more machine like than red.

That looks good! I overpaid again for some boots and pants so all three of my T1's match.

Yea the plates aren't always in the same place. When you remove them there is an outline where they are supposed to go, but don't always end up there.

The stand I used was completely blank and the nameplate wasn't pre-attached. I was using the lines of your decal as my guide but alas when the hand slips the hand slips. Fortunately it wasn't a disaster.

Oh and I also went the ebay route for more pants, I'm probably just gonna keep missing them on Toy Anxiety and I don't have much patience, wanna get these figures up to a particular spec sooner rather than later so that I can be done with them and just admire them. So overpay I did.

I noticed a ''Police Station Assault T-800'' decal in your last set, that's really got me thinking I need one of those aswell :lol I'm probably gonna come back to you with another list of wants if you have the time.

 

[Eterniandreams]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 11/18

Hi,

Do you also do decals for the dynanic stand?

I could use a ASM 1 decal for that.

 

[tbay]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 11/18

Wow, that brushed aluminum looks really good. Could you do the robocop decal I asked about in that material?

 

[EVILFACE]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 11/18

Hi,

Do you also do decals for the dynanic stand?

I could use a ASM 1 decal for that.

Is that the HT DX style stand? If so, yes.

Wow, that brushed aluminum looks really good. Could you do the robocop decal I asked about in that material?

Yup, it is chrome on brushed aluminum.

 

[EVILFACE]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 12/22

Next round!!! Shipped out today!!

 

[MwNN]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 12/22

Awesome work as always!!!
Fantastic logos! Fun to look at!

 

[roybatty]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 12/22

amazing as always, cant wait! ehehehehhe

 

[stshammgod]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 12/22

Who the heck is making a Clu from Tron Legacy? That I gotta see!

 

[tenpacstan]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 12/22

Beautiful work!

 

[tbay]

Re: Evilface's Fourth Circle of Hell - Stand Decals - Updated 12/22

Love seeing your work, especially when there's stuff for me in there! Great round.