Muscular Thighs and Calves, Neck Pegs, Long + Short ankle pegs for Customizing Bodies

[ashkanls]

About the BOOTS people keep asking about the color..... I add dye to the resin when Im pouring the boots so I can do almost any color but it will never be the exact yellow, red, blue, pink so on...

Its impossible for me to match the same hue on two different resin pours so the best thing to do is paint it with one or two coats when you get it to what you want.

 

[Groovy34]

actually 10.25 isn't a bad height I think I can make you know what work with that height.

and as far as the feet goes if it's not the right shade for bats or sups I am not worried I can always paint them. since im doing a true royal blue in latex for bats and a bold red for superman as long as it's the base color for it to grab hold I'm golden.

so your doing a set of 5 long ankle post for how much?
or are they each I got a bit confused on the 1st page.

 

[ashkanls]

actually 10.25 isn't a bad height I think I can make you know what work with that height.

and as far as the feet goes if it's not the right shade for bats or sups I am not worried I can always paint them. since im doing a true royal blue in latex for bats and a bold red for superman as long as it's the base color for it to grab hold I'm golden.

so your doing a set of 5 long ankle post for how much?
or are they each I got a bit confused on the 1st page.

5 sets of any size pegs are $20. And I always send a few extra if I have them.

 

[Aneses]

Interested about the following:

- Boots, 1 pair $15
- Neck peg and connector 4 for $25
- International shipping $8
---------------------------------
- Total: $48 Isn't it?

 

[ashkanls]

Interested about the following:

- Boots, 1 pair $15
- Neck peg and connector 4 for $25
- International shipping $8
---------------------------------
- Total: $48 Isn't it?

Yes it is.

 

[Aneses]

Yes it is.

Ok, money sent. In the Paypal payment message I wrote: ANESES
Thanks! :hi5:

 

[Bluetooth]

Hello, interested in the 10 for $30 ankle connector set

- 5 short
- 5 long

Shipping to Brazil is still $8?

Are these still available?

thanks and regards!

 

[ashkanls]

Hello, interested in the 10 for $30 ankle connector set

- 5 short
- 5 long

Shipping to Brazil is still $8?

Are these still available?

thanks and regards!

Yes they are available and shipping is $8.00. Thanks

 

[Hidden Jitsu]

Just wondering how you get the leg of a hot toys buddy to fit the calves? Or do they slide over the existing ?

 

[ashkanls]

Just wondering how you get the leg of a hot toys buddy to fit the calves? Or do they slide over the existing ?

You remove the factory calve and plug mine on.....

 

[Hidden Jitsu]

You remove the factory calve and plug mine on.....

Thanks for that:hi5: but does the calve just pull of or does it need splitting in 2? As I don't want to ruin the body I have you see.

 

[ashkanls]

Thanks for that:hi5: but does the calve just pull of or does it need splitting in 2? As I don't want to ruin the body I have you see.

It just pulls off if it its a TTM19 and below.

 

[BB&WSF]

Looking for foot pegs meant for TDKR DX12. Do you have 'em ash? And would one need that small foam thing in the middle too.

 

[ashkanls]

Looking for foot pegs meant for TDKR DX12. Do you have 'em ash? And would one need that small foam thing in the middle too.

Those are just long pegs. Purpose of the foam is if the body is heavy it has a little more support so the ankle doesnt bend with the figure topples. Dx12 without the foam should be just fine.

 

[Username]

Looking for foot pegs meant for TDKR DX12. Do you have 'em ash? And would one need that small foam thing in the middle too.

If the figure is heavy and you don't have that foam, cut strips of black insulating tape and wind it round to do the same job.
You can also attach the long pegs to the leg, and wrap tape around from the ankle, to stabilise it.
If you maintain the diameter of the ankle, the peg can still move, just not a huge amount.

 

[BB&WSF]

Those are just long pegs. Purpose of the foam is if the body is heavy it has a little more support so the ankle doesnt bend with the figure topples. Dx12 without the foam should be just fine.

Thanks! I will actually be using the DX12 boots with my BB figure, so hopefully it should work.

@Barry: Thanks a lot for sharing the tips! :duff

 

[olbertfrog]

Ash, do you have muscular neck pegs (and their connectors)?
Thanks

 

[ashkanls]

Ash, do you have muscular neck pegs (and their connectors)?
Thanks

Muscular neck pegs?? Not sure what you mean by that. Can you send me a link of one on ebay or a google pic and I can cast it.

 

[olbertfrog]

Sorry should have been more specific
The peg you sell already fit ttm19/20 muscular bodies.
I meant those that came with the originals t800, barney ross, bane bodies.
Like this :
https://www.ebay.fr/itm/Hot-Toys-TE...0455?pt=US_Action_Figures&hash=item20d524c5f7

Dunno if you also need to recast a t800/barney ross/bane Neck connector too.
I just tried one on a ttm19 Neck connector and it works but its a pretty tight fit.
Could break with resin.

 

[annihilate22]

Ash, would you happen to have HT Luke pegs - I'm looking for:

4 neck pegs, and 3 hand and foot pegs.